Pcb designing

Hello Sir. I can complete this project perfectly. I completed LED display board design before. I have 10 years good experience of hardware development. I have completed a variety of embedded system design and programming by using microcontroller, arm, etc Board PCB design have been completed by using Altium and Protel99SE. Hope to cooperate with you.

I have more than 7 years experience in PCB design with eagle and altium design software .so i can do your job within a time limit with your satisfaction.

Hello I am an eletronic engineer and I have developed the LED Matrix panel for animation image and video and smart mirror. I've designed the PCB board and firmware. For this project, I can develop the prototype and product and source it to you. I can manufacture the prototype in China. After checking the prototype, I will provide the final design the firmware. I am happy if you can discuss further details with me. I am looking forward to your response. Thank you.

Hello We are already have experiance in the domain. we are designing the led p10 based token system and many more plz contact us for meore details About Us We are the team of expert with great experience in there field as listed below. Providing technical service form POC to Prototype till Production setup. 1. Industrial Automation 2. PCB Designing & Manufacturing. 3. Hardware Programming. 4. Home Automation. 5. Internet of Things. 6. Robotics. 7. R&D in electronic and Electrical. 8. STM, Arduino, Raspberry Pi, Atmel, PIC, Node MCU (ESP8266 & ESP32).

Hello How are you? Thanks for your posting job. I have read your project requirements and I am 100% sure I can complete your project perfectly. I have 15 years experience in Circuit & PCB layout design and Microcontroller Firmware design. I will do my best to give you satisfactory results if you hire me. Please discuss about your project in more details. I can deliver your job efficiently within timeline. If you hire me, I think you won't regret. Best regards. Thank you Koba

Hi Sir, I am an Electronics Engineer currently working as an Integrated Circuit Layout designer. I have worked designing Digital and Analog circuits in the past, and have vast experience designing PCBs using a variety of software tools (as Altium Designer, Cadence Allegro and KiCAD). Please contact me so we can discuss more about your project. I can guarantee a first class work, offering unlimited reviews until you are completely satisfied with the final product. Regards,

Dear Sir, I hope you are doing well. Experienced in PCB designing, I have been working in the concerned field for the past 10 years. I have designed PCBs for a variety of microcontrollers, microprocessors, FPGAs and APSOCs as well as analog and digital circuits. I have experience in designing single sided, double sided and multi-layered PCBs. I am into fields of design and development of customized consumer and industrial electronics projects and dedicated computer systems. I mostly base my work, but not limited to, on ready platforms like Arduino, RPi, NODE-MCU, etc. to minimize the development time. I have designed and developed various data acquisition systems, data monitors, data loggers, IoT systems, process controllers, parameter controllers, PID controllers, etc. I am interested in working for you and would like to know about your project in more detail so that we can help you better. Following are the deliverables that We can provide you with: 1. PDF: Schematics, PCB Artwork, 3D view of PCB 2. Source files: Schematics and PCB file in Altium 3. 3D step file of the PCB 4. Gerbers 5. NC drill files 6. BOM 7. Firmware/Software/Codes/Sketches 8. Prototypes and mass production. You can have a look at my profile for some of the introductory and currently completed projects. I would be really honored to have an opportunity to serve you. Looking forward to working with you. Thanks and regards

Hello, I have 10+ years of Embedded product design with multiple domains like a consumer, industrial, automotive, IOT and wearable product. -Hardware architecture design using MCU, controller, and FPGA, as well as low power battery, operated device -Experience in all phases of product development from prototyping to mass production -Experience in Schematic and high-speed PCB layout board design with multilayer PCB design, Blind & Buried Vias in HDI Design. -Expertise in hardware testing and troubleshooting/root cause -Working experience on power management system design with Buck-boost, Battery charger, and fuel gauge, USB3.0 Ctype and PD charging, POE and etc -Expertise in design and simulation of analog circuits -Experience in Microprocessor and microcontrollers like NXP, ST, Microchip, Marwell, Qualcomm, MediaTek, TI, Renesas, and Atmel -Exposure in mechanical design review -Expertise in wireless SOC with Bluetooth, WIFI, 4G, Lora, Zigbee from NXP, Nordic, Ublox, Qualcomm, Cypress, Broadcomm, TI, ESP, Silabs, Microchip -Experience in wire interface USB2/3, SPI, I2C, UART, HDMI, Ethernet, SDIO, MIPI-CSI/DSI, CAN, Modbus, RS232, RS485 -Expertise in solving problems of EMI/EMC -EMI / EMC compliance testing and product certification like CE/FCC/UL and etc Also, We have a team for software development, firmware development as well as CAD design. Let me know if you need help from me. Thanks. --Alpesh

Hello sir .I am manish Kumar tha best electronic man . Your project have in 3 day complete and charge 2000 inr . sir please request ?? your project send me .and you are chill and happiness

hi..I have more than 8 years experienced in circuit design and development. in my past I have designed lot of pcb for company..I can design best way without emiemc problem

Around 15 years of experience in electronics and 5 years of experience in high speed PCB design, sr Hardware Design Engineer. Developed a lots of pcb for automation, networking and power electronics.

I've 5 years working experience in designing and developing various IoT and Embedded System. I'm working with various pcb software like EasyEDA, Proteus, EAGLE, Kicad etc. and also I've working experience at Satellite Project which makes me the perfect in this field. Thanks & Regards.

Hello. How is it going? I am draftsman and industrial designer. I can provide you designs, 3d files, renders and plans to manufacture. You can take a look to my profile to see what I do. Hope you like it and we can work together.

dear sir, we are manufacturing company based in china. We have experience in product design and manufacturing. We can redesign your pcb and make samples and proceed for approbation of your product to be conform to CE and FCC so that you can sell it in europe and north america. We are your guarantee to the success of your product. Please contact us for more details. Note that the bid here is only for reference, after signing your company NDA and review your current design we can give you an accurate quote for the NRE cost and production cost. kind regards

I have experience in embedded system. Deep experience in hardware design and manufacturing. If you give me an opportunity and more elaborate your requirement, i cam help.

Hi,I am Amit here from India with 10 years of Experience in PCB design and Specially In Displays so I can support you on this project.

13 years experience in PCB deaign with sifferent softwares. Electrical knowledge in different areas. Reliable and committed