Antenna designtrabajos
My name is Troy. I have a small (for the moment) WISP in Medellin Colombia. I am using MikroTik routers exclusively in my network. I do have some antenna installs that are Ubuquiti but everything else is MikroTik. I need and an IT Engineer/Technician that is extremely familiar with WinBox to do the advanced programming on the routers. I would prefer someone that is "expert" level. I can do all the initial programming and get things up and running, but the finer points need someone smarter and more experienced than me. At this moment I need to have the routers checked out and the errors cleaned up. I need the web portal set up and the accounting and RADIUS programmed. I want a typical HotSpot set up done. I want the users to arrive at my website initially and be able to r...
...key-tag style enclosure, so component height and antenna placement must be considered from the start. I’m flexible on the exact silicon—Nordic, Espressif, STM, Semtech, etc.—as long as you can justify part choice against current draw, cost and global availability. Please take the design from concept through to manufacturing hand-off. Deliverables • Complete schematic and PCB layout (KiCad, Altium, or Eagle) • Verified footprints, stack-up and DRC reports • BOM with alternates that are currently in stock • Gerber/ODB++ files, pick-and-place and assembly drawings • Basic bring-up firmware that confirms Bluetooth advertising, LoRa transmission, GNSS fix and motion interrupt • Design notes on battery life c...
I need a fresh, distinctive logo that feels classic and timeless while still hinting at the modern mix of services our local antenna association offers— internet, streaming, linear TV, and mobile. I am picturing refined lines and balanced typography that will age well across print, web, and on-air idents. Core elements I definitely want to see explored are subtle antenna or signal motifs and tasteful technology cues (for example, a smart-device outline worked into the mark). Beyond that, I am happy for you to steer the creative direction—particularly with colour. Please choose a palette you believe best reinforces a trustworthy yet contemporary spirit; I’m open to anything from muted neutrals to a restrained splash of colour if it strengthens the concept. L...
Hi, here is the complete project Objective Design and simulate a compact microstrip patch antenna Target specifications: - Frequency: 2.45 GHz (ISM band - Size: < 15-20 mm (very compact - Thickness (substrate): < 0.8-1 mm - Type: Miniaturized Simulation requirements: - Achieve S11 < -15 to -20 dB at ~2.45 GHz - Impedance matching to 50 ohms - single clear resonance (no multiple unwanted dips Deliverables: - Final CST project file (.cst - S11 plot (1-5 GHz range - Timeline: - Need completion within few hours (urgent Please let me know once you review this and if we can proceed, I'lI confirm immediately. Thank you.
...12 V AC relays • Controller PCB – AVR32DD32 MCU with four MAX31865 RTD ADCs and RS-485 bus • UI PCB – ESP32 (external esp32 approved antenna), RS-485 bus, 5-inch EVE4 touch screen, 4 x multicolour LEDs and audio out The Power board, the Controller board and the UI board all matter equally to me in terms of long-term robustness. Schematics for the first two are at a point where I can get them to; the third will be ready for your review within a few days. What I’d like from you 1. Detailed schematic audit highlighting/fixing architectural issues, component stress margins, deratings, safety, EMC susceptibility and reliability traps. 2. Concrete design tweaks or alternative part suggestions that improve MTBF without driving BOM costs signi...
...developing a smartwatch-style device and need a compact micropatch (microstrip patch) antenna that operates reliably at the 2.4 GHz Wi-Fi/Bluetooth band. The form factor has to suit a wearable, so low profile, light weight, and body-proximity tolerance are all important. What I need from you: • A complete electromagnetic design of the patch, dimensioned for common FR-4 or flexible substrates and tuned for 50 Ω matching at 2.4 GHz. • Full-wave simulation files (HFSS, CST, ADS, or similar) showing S11 below –10 dB, realistic radiation efficiency, and a clear far-field pattern when mounted on a small ground plane typical of a watch. • Fabrication-ready outputs—layout, Gerber/ODB++, and a concise design report explaining the stack-u...
...efficiently on both a small solar panel and a rechargeable battery pack. Wi-Fi connectivity is mandatory, and every part of the design has to prioritise ultra-low power consumption so the unit can sit in deep-sleep most of the day yet still wake to trigger a miniature solenoid valve on command. Power architecture The board should accept solar input (≈5-6 V) and seamlessly switch to a lithium cell when sunlight is unavailable. Please integrate an MPPT-style charge controller, battery protection, and a low-loss power-path so the ESP32-C6 always sees a stable 3 V3 rail. Current draw during sleep should stay well under 30 µA. Control section • ESP32-C6 in QFN32 package, antenna matched for 2.4 GHz Wi-Fi • FET or dedicated driver to pulse a 5 V/500...
...an ESP32-based board and now need it translated into production-ready, two-layer Gerber files. Please work exclusively in KiCad so that I can review and maintain the project later. Follow standard IPC design rules throughout: clearances, trace widths, copper pours, silkscreen legibility, and all the usual checks that guarantee a smooth hand-off to any mainstream fab house. The board carries an ESP32 module, its accompanying power-management stage (regulators, protection, filtering), plus several sensors and small actuators. Placement should reflect good RF practice around the ESP32 antenna while keeping analog and noisy digital sections apart. I will supply: • the schematic (KiCad or PDF) • component datasheets and footprints when they are not in the KiCad...
...need a skilled Ansys HFSS user to run full-wave simulations on an antenna design and provide clear Return Loss (S11) results. This is a simulation-only assignment—no fabrication or physical testing for now. What I will share • Geometry or sketches of the antenna and the target frequency band. • Any material data or performance goals I already have. What I need back • The HFSS project file (.aedt) with all boundaries, excitations, and mesh settings correctly defined. • A PDF or image plot of S11 versus frequency that clearly shows the return-loss performance across the band. • A brief note (one page is fine) explaining solver settings, boundary conditions, and any tuning steps you took. At the moment, the exact antenna...
I have a Python script that controls an antenna array and performs object detection with a basic Hamming-windowed FFT. While it works, the range resolution is still too coarse for my needs. I began experimenting with the MUSIC algorithm and even toyed with the idea of adding a continual-learning loop, but I would like a cleaner, expertly implemented solution—whether that is MUSIC, ESPRIT, a refined windowing strategy, or any other modern signal-processing method you can justify. Here is the current landscape: • Language & stack: Python with NumPy, SciPy and Matplotlib. • Key variable: signal-processing methods drive the entire detection chain, so any change must integrate cleanly with the existing pipeline. • Desired outcome: a measurable, demonstrable ...
PCB Design – STM32 I need an experienced PCB designer to create a 4-layer industrial PCB Requirements: * MCU: STM32 * 4G Module: SIM7600G (GPS + LTE) * Power: 12V → 5V (LM2596), 3.3V (AMS1117), battery backup * Inputs: 3× CT + 3× PT (with protection & filtering) * Output: Relay-based MCCB trip (optocoupler isolated) * Extra: MPU6050 (I2C), LEDs, buttons, UART debug Key Design Points: * 4-layer PCB (GND + power planes) * Proper HV/LV isolation (8mm clearance) * EMI/EMC-friendly layout * RF layout for 4G antenna (50Ω) Deliverables: * PCB design files (KiCad/Altium/EasyEDA) * Gerber + BOM + Pick & Place * Ready for manufacturing Looking for: * Experience in industrial PCB design * Knowledge of power + RF + protec...
Online Booking System with SMS Confirmation, Technician Scheduling & On-The-Way Alerts Project Description: I am looking for an experienced developer to build a fully automated online booking system for my website, . My business provides services across Melbourne including TV antenna installations, TV wall mounting, CCTV, and home theatre setup. Customer Booking Requirements: Customers must be able to: select a service choose a date choose a 2-hour time window enter their details including name, phone number, address, and notes submit the booking online Time Slot System: I have 3 technicians, and each technician can handle 4 jobs per day maximum. Available booking windows are: 8:00 AM – 10:00 AM 10:00 AM – 12:00 PM 2:00 PM – 4:00 PM 4:00 PM – 6:00 ...
...professional to evaluate the structural integrity of a roof-mounted antenna on a flat concrete roof. This is on the 18th floor roof of a downtown building in Buffalo. We will attache 2 OTA and one Dish Network dish to existing pole mounts. Attached are samples of what we have installed elsewhere. The Dish is a standard residential unit, the antenna's vary in shape, but are aluminum, so weight doesn't vary much. Key Requirements: - Assess the stability and strength of the antenna installation - Identify any potential risks or needed repairs - Provide a detailed report with images and recommendations Ideal Skills and Experience: - Experience with structural assessments, especially on concrete roofs - Knowledge of antenna installations and potential st...
We are in the process of making a Helmet mounted RF based communication module. Currently PCB design is in progress. we need a rugged product for which we are looking for a product designer Current status: What we have : 1. RF module, list of components are mentioned below i. K-type female jacks ii. C- type charging port iii. Buttons on PCB (all buttons will not be used) 1. Power 2. Vox to PTT 3. PTT 4. Volume increase decrease - 2 buttons 5. Channel increase decrease - 2 buttons iv. Antenna connector v. Batter connector vi. Lights - 2 Led Requirement: End to end solution with regards to design. This will be design centric project with, where PCB will be designed first basis the product design. The product designer team will suggest the placement of com...
...with reader ID, antenna port, RSSI, and any other metadata the Zebra API exposes. • From the stored data I want to filter by date, reader, or tag and export to CSV/PDF, plus run simple counts, dwell-time, and read-rate charts inside the app. Preferred tech stack C# /.NET or another modern Windows-friendly language is fine as long as you use the official Zebra SDK or documented REST endpoints. Deliverables 1. Compiled installer or portable EXE. 2. Full, well-commented source code. 3. SQL schema or setup script for the database you choose (SQLite, SQL Server, or similar). 4. Short user guide covering installation, configuration of readers’ IPs, and report generation. Acceptance criteria • Reads appear on the UI within one second of the tag passi...
Bowtie Antenna Design Report covering all the design aspects.
...need a skilled Ansys HFSS user to run full-wave simulations on an antenna design and provide clear Return Loss (S11) results. This is a simulation-only assignment—no fabrication or physical testing for now. What I will share • Geometry or sketches of the antenna and the target frequency band. • Any material data or performance goals I already have. What I need back • The HFSS project file (.aedt) with all boundaries, excitations, and mesh settings correctly defined. • A PDF or image plot of S11 versus frequency that clearly shows the return-loss performance across the band. • A brief note (one page is fine) explaining solver settings, boundary conditions, and any tuning steps you took. At the moment, the exact antenna...
**PCB Design Brief — Tl Media Dock (Prototype v1)** ## Overview This project is to design a **KiCad PCB for the Tl Media Dock**, a hardware device that reads physical **Media Volume cartridges**. The dock is responsible for: * reading SD card data from cartridges * reading NFC tags for cartridge identification * controlling a small display * providing system control logic The cartridge itself is intentionally simple (passive storage + optional NFC tag). All processing is handled in the dock. This is a **first working prototype**, not a final production board. --- ## System Architecture (IMPORTANT) **Dock :** * Microcontroller * NFC reader * Display control * Power management * Edge connector interface **Cartridge :** * microSD card * passive NFC tag (no acti...
...and thermodynamic constraints • Detailed CAD assembly with material specs and mass breakdown • Propulsion design sheet (solid, hybrid, or liquid—justify choice), including thrust curve and chamber analysis • Avionics architecture: sensor suite, flight computer layout, antenna gain study • Control algorithms and simulation results (MATLAB/Simulink or Python) proving closed-loop stability through max-Q and vacuum phases • Manufacturing plan with tolerances, suggested suppliers, and costed BOM • Ground operations checklist and safety documentation • Recovery concept (parachute, propulsive, or hybrid) with impact energy calculation Acceptance criteria The final design must show, through simulation, a minimum ap...
I have a dual-band RF switch already drafted in Altium that lets one shared antenna handle both 433 MHz (primary) and 470 MHz LoRaWAN links. Before moving on to the board, I need fresh expert eyes on the schematic. You will receive the design as a PDF export. I’m most concerned about three areas: • Signal switching accuracy – verify the detector logic reliably senses the 470 MHz burst and that insertion loss, isolation, and TX/RX paths stay within spec on both bands. • Component placement – confirm the RF switch IC, matching network, SAW filters and biasing parts are arranged to minimise parasitics and avoid crosstalk. • Power management – check the regulator choices, decoupling strategy, and any GPIO level-shifting that could intr...
I need an electronics engineer to design a complete circuit schematic and PCB layout within a 95 mm × 95 mm board size. The PCB will integrate an ESP development board, a 12V relay, a GSM module, and a common power supply for all components. Detailed Requirements: 1. Microcontroller Section ESP32 development board All required pins must be brought out / interfaced clearly Antenna keep-out area should be considered for WiFi 2. Relay Section 12V relay (30A) Optocoupler-based isolation preferred Transistor + flyback diode must be included Screw terminal for load output 3. GSM Module Section SIM800 Proper SIM slot footprint Audio pins not required 4. Power Supply Section Input: 12V DC Regulated outputs: 12V for relay 5V for GSM module 3.3V for ESP Buck converter preferr...
I need an experienced 3D modeler to enhance a vehicle .OBJ file using reference images. The model should be detailed and 3D print-ready. Requirements: - Add moderate details: handles, seams, grille, antenna. - Thicken tires slightly, keeping original scale, and merge with body. - Deliver a single-object, watertight .STL file (no separate parts). Ideal skills and experience: - Proficiency in 3D modeling software (e.g., Blender, Maya). - Strong attention to detail. - Experience with 3D print preparation. - Ability to work from reference images accurately.
I need a compact PCB built around a Nordic Semiconductor SoC that wil...requirement is Thread connectivity, so please choose the Nordic part, RF front-end and antenna configuration that give reliable range while keeping the overall bill of materials within the roughly 70 € target called out in the brief. Once the component set is frozen, you will capture the schematic, lay out the board for low-power operation, and deliver production-ready Gerber files along with a clean, costed BOM that meets EU sourcing availability. Deliverables • Schematic (Altium, KiCad or Eagle) • PCB layout & Gerbers • Costed BOM capped at ~70 € • Basic manufacturing notes (stack-up, drill table, assembly guidance) I am happy to answer questions quickly so yo...
...graduate-level research project that merges smart textiles with security screening: an item of electronic clothing able to detect concealed drugs by combining millimeter-wave sensing with an onboard AI classifier. Where I am right now • Concept development for the millimeter-wave chip placement and antenna layout is underway, but I need an experienced hand to transform these early sketches into a fully realised design and working prototype. What I need from you • End-to-end design and prototyping of the garment, selecting suitable fabrics, conductive threads, flexible PCBs and power management solutions that can live comfortably inside everyday clothing. • Integration of both technologies—millimeter-wave chips for pene...
...path for the haptic actuator. A multilayer PCB layout optimized for size, antenna performance, battery life, and ready for a standard SMT assembly line. Full manufacturing data (Gerbers/ODB++, pick-and-place, drill files), a clean BOM with active part numbers in supply, and the editable project file (Altium or KiCad preferred). Basic DFM and signal-integrity checks passed so the first prototype round goes smoothly. Specific Technical Requirements (based on v3 spec drawing attached): Enclosure target: 34mm × 34mm × 8mm 3-axis IMU sensor (LSM6DSO or BMI270 recommended) – must be placed perfectly central on the PCB for accurate posture detection. Ultra low-power BLE SOC (nRF54L15 recommended or nRF52840) with proper antenna keep-out zone. Compact LRA haptic ...
I manufacture high-performance base station antennas and currently ship only within the United Kingdom. The product line is proven, pricing is competitive, and the factory is ready for larger volumes; what I now need is a clear path to new markets. My immediate focus is on France, Canada, Australia, the USA, Spain and Germany. If you have experience launching RF or telecom hardware in any of these regions—whether through direct B2B sales, setting up distributors, or securing integration partners—I’d like you to map out and begin executing a go-to-market plan. Here’s what I expect as concrete deliverables: • A brief market-entry strategy for each target country, highlighting certification requirements, primary sales channels, and key potential buyers or di...
I need a complete, practical system that carries live chanting and prayers from our temple and plays them through a roadside speaker roughly 5 km away. The audio only has to be standard-quality speech and music, but it must stay clear, continuous, and sync correctly with the live feed in the sanctum. Your job is to specify, price, and integrate everything—transmitter, receiver, antenna choice, power amp, weather-proof speaker, control electronics, plus the small software layer that captures the temple microphone signal and pushes it over the air. Any off-the-shelf modules are fine, yet I still want a clean bill of materials showing individual hardware costs and a separate line for your development time so the trustees can approve the budget. Key requirements • Live ...
...telecom engineer-electrician to handle a full-cycle project on a commercial site. The scope covers both a brand-new installation and improvements to an older system already in place, so you’ll be working on fresh infrastructure as well as live equipment. The main tasks are clear: • Installation of RF equipment, including cabinet placement, coax jumpers, grounding and final sweep tests • Rooftop antenna setup—safe mounting, alignment and weather-proofing on an existing flat roof • Electrical wiring and ongoing maintenance to make sure all gear stays powered, bonded and code-compliant You’ll coordinate with building management for roof access, follow all commercial safety standards and provide concise documentation of wiring diagrams, IP addre...
I'm looking f...create a compact PCB for a wireless EEG system intended for consumer electronics. The system will need to feature: - Bluetooth connectivity - Mobile app integration - Rechargeable battery Ideal skills and experience: - Expertise in PCB design for consumer electronics - knowledge of low-noise analog design - biosignal acquisition - Experience with Bluetooth and mobile app integration - Knowledge of power management for rechargeable batteries - knowledge of RF antenna layout for BLE Scope of work: Full schematic design PCB layout (4-layer, low-noise analog design) Component selection (BOM) Gerber + manufacturing files Basic firmware to stream EEG data over BLE Please include examples of previous low-noise analog or biosignal design...
...objetivo é dar continuidade a um desenvolvimento existente, então o design deve ser funcional, confiável e pronto para produção. ENGLISH: I need a professional to design a PCB in EasyEDA (schematic + layout) using the ESPRESSIF ESP32-C3 (C2838500) - The project must include: 3.3V power supply (3V3) and GND Exposed GPIOs: 1, 2, 3, 4, 5, 6, 7 UART (TX/RX) LED on GPIO 8 BOOT button RESET button Wi-Fi antenna (proper RF layout) Requirements: Clean and well-organized board All connections accessible via pin headers Complete development: schematic + PCB PCB with 2 or 3 layers (optimized for JLCPCB manufacturing) The goal is to continue an existing development, so the design must be reliable, functional, and production-read...
...module—onto a multilayer PCB small enough for a wrist-worn form factor. Biosensing • The design centres on a heart-rate monitor as the primary biosensor. Signal quality, noise immunity, and optimal placement on the board and inside the enclosure all have to be engineered with production-ready accuracy. Power management • Fast-charge capability and ultra-low standby consumption are non-negotiable. Battery chemistry, protection ICs, and charging topology should be selected and simulated so that typical daily usage still leaves ample reserve before the next charge cycle. Connectivity & processing • A Bluetooth Low Energy or comparable wireless SoC will stream data in real time to a companion mobile app. Antenna layout, impedance matching, and...
...reference while building and documenting my own project. My project is “Design and System-Level Integration of Antenna Microwave Feeding Network”. The main idea is to design a microstrip-based RF front-end / feeding network for antenna integration, starting from hand calculations, then building the physical EM models in HFSS, optimizing them, and finally exporting the HFSS blocks into Twin Builder for full system-level validation. The project requires realistic microwave design practice, electromagnetic modeling, system integration, and performance evaluation using HFSS and Twin Builder. The project includes multiple required components, not just one simple line. The tasks include: Microstrip transmission line design Unequal T-jun...
I need a complete Ansys HFSS model of a microstrip antenna working in the high-frequency band 140 GHz. My aim is to make array and to analyse radiation pattern, impedance matching and gain exactly as they appear in a research paper I will share after kickoff. Your job is to recreate the antenna geometry from the paper, set up the correct substrate, ports, and boundary conditions, run the solver, and then fine-tune dimensions so the results align with the publication. Acceptance criteria • |S11| ≤ –10 dB at the paper’s centre frequency • Realised gain within ±0.5 dB of the reported value • 2D/3D far-field plots that visually match the paper’s patterns Deliverables 1. Native .hfss project containing geometry, setup, and pos...
...have to support: • Voice calls • Text messaging Both Android and iOS users should be able to pair, place or receive calls, and read messages seamlessly. My expectation is that you will design the electronics (schematics, PCB, antenna layout), choose components that meet worldwide 4G bands, integrate a robust battery management system, and supply the low-level firmware that drives the modem, BLE stack and power states. If you can also oversee enclosure engineering or early prototyping, let me know—that’s a plus. Please outline your experience with cellular IoT modules, smartwatch or wearable PCB design, and any shipped products that prove you can balance RF performance with tight power budgets. I am ready to move quickly once I see a cle...
...y power source without any conflict or backfeeding between sources. The design should include comprehensive protection mechanisms such as reverse polarity protection (preferably MOSFET-based), surge and transient protection (TVS), and fuse/PTC safety. Efficient power conversion is required using a buck converter for stepping down to 5V followed by low-noise regulation to 3.3V for the ESP32. The LiFePO₄ charging system must use a dedicated charger IC with appropriate voltage and current settings along with full battery protection features. The ESP32 section should follow best practices including proper decoupling, reset and boot circuitry, and strict antenna layout guidelines with no copper or ground under the antenna region. The board must include an internal USB T...
...for fabrication, but before I release the Gerbers I want a fresh set of expert eyes on it. The priority is to confirm that every electrical connection is rock-solid—power rails, ground returns, high-speed signal lines, reset/boot strapping pins, antenna feed, the lot. Please run a full Design Rule Check (DRC) with the tool of your choice and then go beyond the automated results with a manual review of power distribution, decoupling strategy, trace widths, via placement, differential pairs and any impedance-controlled lines. Once you receive the design files, I’d like you to: • Clear all DRC errors and point out anything that could still be marginal even if it technically passes. • Flag potential EMI/EMC trouble spots, thermal bottlenecks an...
antena theory using ANSYS electronics
...(typically VIN, GND, SCL, SDA) so the modules plug in directly without adapter wires. As a bonus, I would like a battery voltage divider (two resistors) connected to GPIO 34 (ADC1 channel) so the firmware can read the battery percentage and display it on screen. Also include test points on key power rails (3.3V, VBAT, 5V USB) and maintain a proper keepout zone around the ESP32 module's antenna area per Espressif's RF design guidelines. Deliverables I need: complete schematic (KiCad preferred, Altium also acceptable), finished PCB layout with copper pours and proper grounding, manufacturing-ready Gerber files compatible with JLCPCB or PCBWay, a Bill of Materials with LCSC/JLCPCB part numbers where possible for easy assembly ordering, a pick-and-place file if SMD c...
Design of a complete 2-layer MVP PCB for an ESP32-S3 based NFC Audio Player, including schematic, layout, and production files. Scope of work: Complete schematic design in KiCad (editable source files) 2-layer PCB layout with proper zone separation (NFC / audio / power) NFC antenna clearance and keep-out respected ESP32-S3 RF antenna ground clearance respected Decoupling capacitors properly placed (< 3mm from each IC) All critical issues from the previous audit corrected (amplifier, regulator, boot pins, decoupling) BOM optimized with LCSC/JLCPCB references (stock verified) Production files: Gerber, Pick & Place, STEP 3D Full DRC/ERC review before delivery Key components: ESP32-S3-WROOM-1 (MCU) PN532 NFC module (SPI) MAX98357A (I2S DAC + Class-D amplif...
Looking for an experienced hardware designer to handle both PCB design and 3D enclosure for a small wearable BLE device. --- What We Need - Circular or elliptical PCB, ~30–35mm, designed to fit inside a bracelet enclosure - Bare nRF52840 SoC with proper RF layout and antenna design - Manufacturable via JLCPCB / JLCPCB Xiao Fusion / PCBWay with PCBA service - Bracelet-style enclosure housing the PCB, Li-Po battery, vibration motor, and capacitive touch sensor — clean minimal aesthetic, designed for FDM/SLA prototyping with production scalability in mind --- What's Already Done - BLE firmware is complete and tested --- What We Have in Mind (Open to Suggestions) - Haptic feedback (motor driver) - Battery fuel gauge - Capacitive touch sensor - Chargi...
This is a MSFS 2024 project for the Fenix a320. I simply need two extras added: a Satcom antenna on the fuselage and window plugs along the cabin randomly to emulate window shades. The base aircraft model itself must remain untouched—you will work in Blender, create the new geometry, UV-map it, apply a realistic texture set, and then position and parent the parts so they export cleanly back into the sim. Level of finish: moderate, with convincing baked textures rather than ultra-dense geometry. I will supply clear reference photos that show dimensions, placement, and the metallic surface look I’m after; use these to match shape and panel lines closely. Deliverables • Blender file with Satcom and window plug meshes, UVs, and metallic PBR textures • Export-...
I need a complete, practical system that carries live chanting and prayers from our temple and plays them through a roadside speaker roughly 5 km away. The audio only has to be standard-quality speech and music, but it must stay clear, continuous, and sync correctly with the live feed in the sanctum. Your job is to specify, price, and integrate everything—transmitter, receiver, antenna choice, power amp, weather-proof speaker, control electronics, plus the small software layer that captures the temple microphone signal and pushes it over the air. Any off-the-shelf modules are fine, yet I still want a clean bill of materials showing individual hardware costs and a separate line for your development time so the trustees can approve the budget. Key requirements • Live ...
...while syncing over Bluetooth. I already have the industrial design envelope; now I need an experienced hardware engineer who can turn that concept into a production-ready PCB. Scope • Create the full schematic, selecting a low-power MCU/BLE SoC, optical heart-rate sensor (PPG), 3-axis accelerometer, and power-management IC for a rechargeable Li-Po cell with on-board charging. • Lay out a rigid or rigid-flex board that fits the tight enclosure constraints and maintains signal integrity for the optical sensor and antenna. • Optimise for battery life, drop resistance, and ease of automated assembly. • Produce a complete manufacturing package—BOM, Gerber/ODB++, pick-and-place, assembly drawings—and be available for one design rev...
This is a MSFS 2024 project for the Fenix a320. I simply need two extras added: a Satcom antenna on the fuselage and window plugs along the cabin randomly to emulate window shades. The base aircraft model itself must remain untouched—you will work in Blender, create the new geometry, UV-map it, apply a realistic texture set, and then position and parent the parts so they export cleanly back into the sim. Level of finish: moderate, with convincing baked textures rather than ultra-dense geometry. I will supply clear reference photos that show dimensions, placement, and the metallic surface look I’m after; use these to match shape and panel lines closely. Deliverables • Blender file with Satcom and window plug meshes, UVs, and metallic PBR textures • Export-...
...comfortable in both. First, I am developing a low-frequency (30–300 MHz) microstrip antenna. You will take my initial sketches and performance targets, model the antenna, iterate dimensions for optimal impedance match and gain, and provide fabrication-ready Gerber files plus a brief simulation report (HFSS, CST, or comparable). If you already have proven techniques for low-band microstrips, please outline them when you respond. Second, I have a backlog of structured data that must be transferred from scanned sheets into Excel/Google Sheets with 100 % accuracy. Clear, consistent formatting is essential; the dataset will later feed directly into my RF analysis scripts. Deliverables • Complete microstrip antenna design files (schematic, EM simulati...
...performance. What I imagine is a compact, self-contained module (belt clip, pendant, or similar form factor) that combines three core functions: 1. Real-time RF spectrum monitoring across common surveillance bands, with an on-device or smartphone-linked display that flags unusual spikes. 2. Adaptive or broadband RF attenuation—whether through active cancellation, resonant materials, or smart antenna tricks—to reduce power levels that actually reach my body. 3. Optional direction finding so I can walk a few steps and watch the signal strength change, giving me a clue about where it originates. If you have experience with SDRs, miniature shielding materials, Faraday fabrics, phased-array or null-steering antennas, please outline how you would bring those too...
PCB Design Brief Timeline Media Dock Controller Board This project requires a KiCad PCB design for the first prototype of a open source Media Dock. The dock is a hardware reader device used to interact with physical Media Volumes, which are media cartridges containing either storage media (SD card) or NFC identification tags. The board will be installed inside a dock enclosure and connected to a front display. Core Features The PCB must include support for the following components: Microcontroller ESP32 module (recommended) or equivalent microcontroller suitable for handling: SD card access NFC communication display control system logic NFC Reader The board must include an NFC reader chip (such as PN532 or equivalent) used to detect and read NFC tags embedded in...
...hardware engineer to design a compact PCB/FPC for this device. This is a very small wearable device, so experience with ultra-compact electronics is essential. Device concept: Smart ring with biometric sensors and Bluetooth Low Energy connectivity. Main components planned: • Nordic nRF5340 BLE SoC • MAX86174 optical biometric sensor (PPG) • ICM-42670 motion sensor (IMU) • TMP119 temperature sensor • nPM1304 power management IC • External SPI Flash memory • Li-Po micro battery Design constraints: • Ring thickness target: 3–3.5 mm • PCB width: approx 5.5 mm • PCB length: approx 26–30 mm semicircle layout • Extremely low power consumption • BLE antenna tuning required Scope of work: •...
This projects requires the design of 2 PCBA's plus wiring and advice on other components with all connections. 1) For BlayzPad, a handheld controller with a display, antenna, ESP32S3 and ESPNOW commununications 2) A BlayzPoint with 133 addressable LED's, SD card, RFID reader/writer, twin 18650 batteries, 2 Speakers, ESP32S3 and ESPNOW communications. Both projects with USB C for flashing and charging.
