Waterproof enclosure for electronics

Estado: Closed
Premio: $120
Propuestas recibidas: 6
Ganador: MKatsarov

Winner

Resumen del concurso

I have a simple Arduino GPS Speedometer for a small boat (a Laser dinghy) that I'm housing in a tupperware container, but the display is hard to read if off-center, and I use a lot of duct tape attaching it to the boat. I'd like a design for a waterproof way of attaching/detaching an enclosure to the boat so it is easy to read from both sides of the boat, and won't come loose if wet.

I'm currently attaching my makeshift enclosure (a 15cm X 15cm X 5cm food container) to the deck with tape. Please see the attached picture of approximately where the enclosure must be positioned. The display I'm using is the adafruit 7-segment (https://www.adafruit.com/product/879), which is hard to read in direct light (facing upwards), but readable if positioned horizontally. Attaching to the mast (approx 6cm diameter) or boom (slightly less) could be a good solution, however it can't obstruct any of the ropes in the area (visible in the attached picture).

I'm looking for a 3d-printable design that can be attached to the boat on one side, and to the enclosure on the other. It can be hot-glued to the enclosure, but can't be permanently attached to the boat.

* I've attached a picture of various windvanes, and how they are attached to a laser mast. This solution could be similar, but my enclosure is much larger/heavier *

Habilidades recomendadas

Winner

Publica un concurso similar

Comentarios del empleador

“He added a modified design after the contest was already won--very considerate.”

dtredger, Canada.

Principales propuestas de este concurso

MKatsarov Bulgaria

0
ahmadnazree Malaysia

0
sonnybautista143 Philippines

0
rayanshockwave India

0
I1enVantev Bulgaria

0
Mynhardt123 South Africa

0

Ver más participaciones

Tablero de aclaración pública

DigitalFlower
- 5 años atrás
oh, missed the deadline >.
- 5 años atrás
rayanshockwave
- 5 años atrás
Pls check entry #4
- 5 años atrás
rayanshockwave
- 5 años atrás
isnt the 15*15*5 box pretty big for your display and the arduino??
- 5 años atrás
I1enVantev
- 5 años atrás
Please tell your opinion on #3 .Thanks
- 5 años atrás
ARTandFASHION
- 5 años atrás
Hi, please tell me do you have any sensors outside this container and why you don't use the arduino with led inside for the better view? Thanks.
- 5 años atrás
DigitalFlower
- 5 años atrás
hi! please wait until the end of the contest, i'll be uploading my entry by then, thank you!
- 5 años atrás
Organizador del concurso
- 5 años atrás
regarding weight, it is essentially a 15cm x 15cm x 5cm container with some electronic components (arduino, 5xAA batteries, half-size breadboard). Unfortunately I don't have the enclosure to weigh it, but it would be less than a pound (1/2 kg) at most.
- 5 años atrás
bryancasares
- 5 años atrás
Hello, could you give me an approximate weight of the enclosure? Since you say its heavier I want to give you an appropiate solution. Thank you.
- 5 años atrás
Organizador del concurso
- 5 años atrás
I've clarified the project, and reduced the scope (since the size of the enclosure itself is still changing). Now only the connection between boat and enclosure is required. Please see the attached picture (of the front deck of a Laser dinghy) for the zone where the enclosure needs to be placed.
- 5 años atrás
armandgomez
- 5 años atrás
Can you please provide more information about it? Some photos of the boat and the electronics would be perfect.
- 5 años atrás
azeemmustaq786
- 5 años atrás
Can you provide more details about it, can you have a chat?
- 5 años atrás
RasheedEqbal
- 5 años atrás
Can you please send me the layout/schematics/photos of your boat and all its component so that I can design it properly.
- 5 años atrás
wharolinsky
- 5 años atrás
if you can send private message i can give you an offer that maybe you will love
- 5 años atrás
wharolinsky
- 5 años atrás
hey sorry would you please let me know what arduino are you using for this? and in which part of your boat it will be putting?
- 5 años atrás